Our EOBD-Facile software

EOBD-Facile functions

EOBD-Facile software demo version

The software EOBD-Facile offered by the team at Outils OBD Facile allows you to use the interfaces of ELM327 type (ELM320, ELM322 and ELM323 are also supported). It enables you to dialogue with your vehicle in order to diagnose a failure.

To get a licence for the full version of EOBD-Facile, go to our boutique.


Download the free version of EOBD-Facile

Compatibility with Windows XP, Vista, 7 and 8. Older versions of Windows are not compatible.


Logo windows 8Logo windows 7Logo windows VistaLogo windows XP




Our software is translated into the following languages:

Functions
Version
Not registered
Registered version
(free)
Full version
(paying)
Connecting to ELM327 interfaces
Self-detection of interface communication parameters
(only USB)
Reading of fault codes (Mode 3)
Deoding of fault codes into text (English)
More than 4000 definitions (P0xxx, B0xxx, C0xxx and U0xxx)
Reading of sensors (Mode 1)
Reading of unconfirmed fault codes (Mode 7)
Continuous reading of sensor values (Mode 1)
In the form of a table
Continuous reading of sensor values (Mode 1)
In the form of a graph

(1 curve)

(4 curves)
Virtual dashboard
Terminal for advanced commands
Continuous recording to sensor values (in a .csv file)
New! Review recordings in graph form
Smart recording triggers
Instantaneous data reading (Mode 2)
Clearing of fault codes (Mode 4)
Reading of permanent fault codes (Mode 10)
TIDs (Mode 5)
OBDMID (Mode 6)
Vehicle info (Mode 9)
CAN bus spy
DOWNLOAD REGISTER BUY NOW


Information about EOBD-Facile

How to get and register the software

  1. Download the software from the Download section
  2. Run the install file "Install EOBD-Facile English.exe"
  3. Connect to your vehicle and use the wizard present in the menu "Register" and "Create a registration file".
  4. Follow the instructions to create a file. Click on this link to send us the file automatically or send it by email to the address (file saved in Documents/EOBD-Facile/Log).
  5. You will receive a reply with a login and an activation key (within 24 hours maximum).
  6. Enter this information in the software using the menu "Register" then "register"
  7. Restart the software

Why is it necessary to register?

Registration will free up additional functions in the software. The log that you send us to register will enable future users to benefit from your experience and create a list of EOBD compatible vehicles and the functions it supports.
Registration is free of charge and only requires a few minutes.

How to get the full version?

Go to our online shop www.boutiqueobdfacile.com and order the full version of the EOBD-Facile software.
Note: If you have bought an interface in the store, you will automatically be entitled to the full version.

What can the software do?

The software is based on the OBD specification concerning engine and transmission computers. This specification was imposed on manufacturers, meaning that all vehicles are compatible, to a greater or lesser degree.

The software can only be used for diagnosis, not to reconfigure an ECU. Unfortunately, the EOBD standard does not include the airbag, ABS or ESP computers. I repeat in red NO DIAGNOSIS OF ABS, AIRBAG OR ESP POSSIBLE. In this case, only the manufacturer's kit can do a diagnosis.

What interfaces are needed to use the software?

Only interfaces based on ELM are compatible with the software. Whatever their reference (ELM323, ELM327) or connection type (RS, USB or Bluetooth).

How can I update the software?

Download the new version from our site in the download section.
Run the installation in the same place as the previous version and restart the software.

Connection problems, error messages!

In this case, open the file "help-EOBD-Facile.pdf" to see chapters concerning these errors.


EOBD-Facile screenshots

EOBD-Facile Reading of fault codes EOBD-Facile Advanced diagnostics EOBD-Facile Sensors EOBD-Facile Oxygen sensors EOBD-Facile monitoring EOBD-Facile vehicle identification EOBD-Facile Dashboard